Diamond Drill Bits: A Girl’s Best Friend!

I adore pendant lights.  All colors, sizes, wattage, shapes, and finishes.  I “window shop” for them on the internet frequently.  Someone must tell me, though, why they are so dang expensive!  Maybe I am just poor, or cheap (ahem – frugal), but I could not bring myself to spend $200 on one measly little light, despite my obsession.

I was browsing at a thrift store one day (which I regularly do for no reason), and saw a beautiful multi-colored glass bowl.  It caught my eye from across the store.  I wasn’t quite sure what I would do with it, so I carried it around the store with me.  I put it down a few times, but only got a few feet away before I ran back and grabbed it and held it tightly, for fear someone else would snatch it up. For the low, low price of $4, I decided to buy the bowl now, and figure the rest out later. You can probably figure out where this is going.

I knew that Home Depot sold pendant light kits, but they are mix and match deals, where you choose the finish of your hardware and some variation of a glass cover.  I, however, bought just the hardware, in brushed nickel.  I am SUCH a rebel.

Herein lies the problem.  The threaded bottom of the hardware is about an inch in diameter, and there is a separate piece that screws on to hold the glass in place.  I had to put a 1 inch hole in the bottom of my new bowl, which required a fancy new diamond drill bit.  My level of excitement over a new drill bit, on a scale from comatose to hyperventilating, was somewhere around flapping my arms in a happy dance when this baby arrived in the mail:

I learned that the “legend” on the right side of the packaging indicates what materials the drill will go through.  There are all kinds of bits for all kinds of materials, such as wood, glass, tile, brick, cement, etc.  This one has the symbols for tile and glass, and shows dripping water at the bottom right, which tells you to keep the material wet while you drill, so that it doesn’t overheat.

I put the bowl upside down in the utility sink in the garage, put the tap on a very slow drip (I was basically water boarding my fancy new bowl), and started drilling.  It is exceedingly difficult to get the hole started, because the bit slips around on the surface of the glass. With some decent pressure, and determination, I finally started making some headway.  It. Took. For. Ever.  My hand cramped.  My neck hurt.  I contracted tennis elbow.  I developed an appetite.  I took several breaks.  But I persisted.  Finally, gloriously, and unexpectedly, I broke through.  Eureka!!!  I was so excited because The Boy had been a naysayer, was amused when the new drill bit arrived in the mail, and I purposely tackled this challenge while he was not home.  And I succeeded!!

I sprinted inside with my now hole-ridden bowl, ripped the packaging off of the pendant hardware, and tried the bowl on for size.

It didn’t fit.

Oh, the frustration.  After I gathered myself, I realized that the hole was just slightly not large enough.  I went back into the garage, still very glad The Boy had not returned, and used the drill bit at an angle to slowly make the hole a little bit bigger.  It took a solid ten minutes, and sounded like nails on a chalkboard, but it worked.  I triumphantly slid the bowl over the threaded end, and screwed on the piece that held the glass in place.  The Boy was most impressed when he came home to this beauty:

She has been hanging out in the new bathroom ever since:

Total cost:  $18.97 (if you do not include the cost of the drill bit, which I am not, since it is a permanent resident of my toolbox now).  You can’t beat that price!  I am currently on the hunt for two large glass urns to make hanging pendant lights for the master bath we will soon be demolishing.  I’ll be sure to update you when they have been located!

2 thoughts on “Diamond Drill Bits: A Girl’s Best Friend!

  1. Please update us more on decorating ideas. We are moving in less than 6 weeks and have more rooms to decorate. After looking at our savings account ( that I decided not to touch) I have decided to get crafty real fast . This will be a must :)

  2. Pingback: Crafting Fail – Fixed! | Pardon Our Sawdust

Leave a Reply

Your email address will not be published. Required fields are marked *